UEFA Champions League live

List of the catalog of this article:

• 1、 How to correct the timing gear of the Volvo D6D engine?
• 2、How to pair the front gear of the Man 11 engine
• 3、UEFA Champions League liveHow to gear the Kubota 3800 engine
• 4, Weichai Guoer engine replacement pump No
• 5、 How does the Deutz 6+dk engine deal with crankshaft teeth and camshaft teeth?

How to correct the timing gear of the Volvo D6D engine?

1. The adjustment method of ignition time is: l) Adjust the contact gap of the breaker, and the contact gap of the breaker should be adjusted first. Because the size of the contact gap of the power offer not only affects the strength of the high-pressure spark, but also affects the ignition time.

2. Alim the crankshaft according to the mark on the crankshaft timing pulley. Generally, the stop point position of the piston of 1 cylinder is required;Install the marking on the timing pulley of the camshaft to align the camshaft, and the position of the double camshaft to the two camshafts respectively; just install the timing belt/chain.

3、. If it is connected by a belt. Align the timing gear of the camshaft and the timing mark of the crankshaft timing gear with the cylinder head and cylinder respectively. If it is a chain connection. Put the three different color chain flaps on the chain.

4. The timing of the engine is the correction of the best time point for intake and exhaust, fuel injection and ignition.

How to pair the front gear of the Man 11 engine

The gear in front of the machine should be right. The gears in front of the German Man engine should be right. This is because the engine has been running.During the process, the correct alignment of these gears is crucial to the smooth operation and fuel efficiency of the engine.

Method: align the crankshaft according to the mark on the crankshaft timing pulley. Generally, the stop position of the piston of 1 cylinder is required; the marking on the camshaft timing pulley is aligned with the camshaft, and the double camshaft is aligned with the two camshaft positions respectively; the timing belt/chain is installed.

Generally, there is an installation mark on the side of one of the teeth of the timing gear. There are three such marks on the idle gear, two of which are adjacent. During installation, the two notation clips on the idle wheel are a mark on the timing gear, and there are two adjacent marks on the gas distribution gear, which are also aimed at the other on the iddler. Just make a mark.

How to adjust the gear of the Kubota 3800 engine

1. The timing of the engine is the correction of the best time point for intake and exhaust, fuel injection and ignition.

2. It is preferable to use a card to jam the timing axle to prevent the shaft from getting stuck during the proofreading of the gear. After that, loosen the top of the shaft on the timing axle to facilitate gear calibration. Then find the colored chain teeth on the camshaft. Then aim the colored chain teeth at the small dots on the camshaft.

3. First, rotate the crankshaft so that the cylinder piston is at the compression stop. For the 4-cylinder engine, first adjust the intake valve and exhaust valve of 1 cylinder, the exhaust valve of 3 cylinder and the intake valve of 2 cylinder. For the 6-cylinder engine, first adjust the intake valve and exhaust valve of 1 cylinder, the exhaust valve of 3 cylinder and 5 cylinder, and the intake valve of 2 cylinder and 4 cylinder.

4. First of all, use a card to firmly jam the timing axle, so as to prevent the axle from getting stuck when proofreading the gear. 2/7 Loosen the top of the shaft. After that, loosen the top of the shaft on the timing axle directly, which is convenient for the calibration of the gear. 3/7 Find the chain teeth. Find a colored chain tooth on the camshaft. 4/7 Chain teeth are aimed.

5. Engine timing is generally divided into two situations. The first is timing chain. There are color marks on it. Formal gears and. The marks on the rear parts of the formal gear are aligned. According to the prescribed standards, the position of most engines on the right time is the position of the stop point of a cylinder compression. The second kind.

Weichai Guoyi engine changes the pump to the tooth is not

and then the mark on the camshaft is aimed at the mark on the gear chamber, allowing the clockwise misalignment of the teeth. After the camshaft is installed, according to the model, reverse the engine to the required ignition time degree (generally there is a little ignition time degree on the engine nameplate), and then the scale on the oil pump to a cylinder.

Weichai does not have a timing mark. You can directly install the gear of the air pump and then time the ignition.The pinion adopts a positive shift. Avoid cutting. Increase the thickness of the teeth and improve the bending strength of the wheel teeth. Reduce the sliding rate of the tooth root. Increase the radius of curvature of the tooth profile and improve the contact strength of the tooth surface.

You can go to the car repair place to repair it, or you can repair it yourself. The steps are as follows: 1. Apply glue well to prevent oil leakage. 2. The inflator pump is installed on the engine. After the front and rear are connected, the connecting pipe joint should not leak air, especially the oil pipe must be connected well, and the oil leakage should not be loose.

Weichai does not have a timing mark. The gear of the air pump can be installed directly. Then turn on the timing of the ignition. There is a mark on the oil pump. At the front end of the oil pump. The mark on a thin steel sheet and the mark on the connecting shaft. You will find it if you carefully check the oil pump and turn it around.

How does the Deutz 6+dk engine pair crankshaft teeth and camshaft teeth?

1. The method of the upper and lower gear pair of the Weichai Deutz camshaft is as follows: first, the scale of the flywheel, rotate the flywheel from the gear ring position to the OT scale, and then there is a small scale for the camshaft and camshaft gear. There is also a scale mark on the timing chamber, and the follow-up wheel is installed.

2. Observe whether the timeline marker on the camshaft gear is aligned with the timeline on the timing shell. If the positive time line is not aligned, it means that the gas distribution phase is wrong, and the camshaft gear needs to be reinstalled until the two engraved lines are marked and aligned.

3. Point the blue card teeth at the small dots on the camshaft. In this way, the correction is completed on time. Related content explanation: The camshaft is a part of the piston engine.Its function is to control the opening and closing of the valve.

4. The timing of the engine is the correction of the best time point for intake and exhaust, fuel injection and ignition.

5. First, turn the crankshaft of the Deutz engine, so that the cylinder piston is in the upper stop position and fixed. Secondly, the timing mark of the Dewitz engine camshaft gear is aimed at the timing mark on the chain and fixed. Then install the crankshaft-driven sprocket and make sure that the timing mark on the chain and the mark on the sprocket are in the same position.

6. The timing gear of the four-cylinder four-stroke diesel engine is right like this. The 0 sign of the two teeth of the crankshaft teeth is the 0 sign of one tooth in the middle tooth, and the 0 sign of one tooth in the middle is in the middle of the 0 mark of the two teeth of the camshaft gear (time gear). At the same time, the two 0-marked teeth of the middle teeth must be used to one 0-marked tooth of the oil pump tooth.