UEFA Champions League

List of the table of contents of this article:

• 1, What are the engine disassembly steps
• 2、 What is the process of disassembling and installing the engine?
• 3, Disassembly steps of the engine

What are the engine disassembly steps

1. Place the engine vertically. Remove the fixing screw of the cylinder head. Note that the screws should be loosened from both ends to the middle, and the screws should be removed three times. Lift the cylinder head, remove the cylinder cushion, and pay attention to the installation direction of the cylinder cushion. Loosen the oil release screw of the oil span shell and drain the oil in the oil span shell.

2. Disassembly of engine fuselage components 1) Remove the fixing screw of the cylinder head, note that the screw should be crossed and loosened from both ends to the middle, and the screw should be removed in 3 times. 2) Lift the cylinder head. Remove the cylinder pad and pay attention to the installation direction of the cylinder pad. Loosen the oil release screw of the oil span shell to release the oil in the oil span shell.

3. The steps for disassembly and disassembly of the engine are as follows: place the engine upright. Remove the intake and exhaust manifolds and the cylinder head outlet pipes. Remove the cylinder head cover. Remove the rocker arm assembly on the cylinder head, remove the boom chamber cover, remove the putter, and take out the boom in order. At the same time, write the sequence number. Remove the cylinder head and gasket.

4. Remove the clutch tie rod, separation fork and transmission shaft, remove the engine support rod and the front and rear support frame nuts; tie the engine with a rope;Hang it down with the engine hanger. Engine disassembly principle: from auxiliary parts to main parts, from the outside to the inside.

5. Engine disassembly steps and methods: Step 1: Remove the intake and exhaust pipes and exhaust pipes of the cylinder head. Step 2: Remove the valve cover. Remove the locking nut of the rocker arm shaft bracket and take out the rocker arm and shaft together. Remove all the putts. And make a good order so that the original friction pair can be maintained during installation.

6. The specific disassembly steps are as follows: Method 1: Unplug the battery wiring when the ignition switch is turned off. Take out the battery. Pay attention to pull it out first and then take it off. Unstighten the fastening bolt of the battery bracket and remove the battery bracket. Place a collection plate under the engine. Unscrew the lid of the coolant storage tank.

What is the process of disassembling and installing the engine?

1. Hello: Release the oil first. Disassemble the exterior accessories. Remove the timing and cylinder head parts, remove the connecting rod and piston. Disassemble the crankshaft.

2. Disassembly steps: To remove the external components of the fuselage, first remove the external parts as required, and remove the motor, generator and other components. Then remove the intake and exhaust manifold, remove the cylinder cover, and then remove the gasoline pumps on both sides, so that the external components of the engine are basically dismantled.

3. Disassembly and installation steps of the car engine valve group Disassembly of the car engine valve group (1) Remove the valve adjustment gasket. (2) Remove the inlet and exhaust doors. Use valve disassembly pliers to compress the valve spring, and remove the lock, spring seat, valve spring and valve successively. (3) Use sharp-nosed pliers to remove the valve lever oil seal.

4. Engine disassembly steps: place the engine upright, remove the inlet and exhaust manifolds and the cylinder head outlet pipes. Remove the cylinder head cover, remove the rocker arm shaft assembly on the front and rear cylinder head; remove the crankshaft ventilation pipe, and remove the boom chamber cover; remove the putter.

engine disassembly steps

1. Disassembly of engine body components 1) Remove the fixing screw of the cylinder head. Note that the screw should be crossed and loosened from both ends to the middle, and the screw should be removed three times. 2) Lift the cylinder head. Remove the cylinder pad and pay attention to the installation direction of the cylinder pad. Loosen the oil release screw of the oil span shell to release the oil in the oil span shell.

2. Engine disassembly steps and methods: Step 1: Remove the intake and exhaust pipes and exhaust pipes of the cylinder head. Step 2: Remove the valve cover. Remove the locking nut of the rocker arm shaft bracket and take out the rocker arm and shaft together. Remove all the putts. And make a good order so that the original friction pair can be maintained during installation. Step 3: Remove the timing gear cover and gasket camshaft.

3, 2 Turn the main switch to the "OFF" position. 3 Remove the outer cover of the car. 4 Dray the engine oil.5 Remove the negative wire of the battery first, and then remove the positive wire. 6 Remove the carburetor and automatically start the thickening valve wire. 7 Remove the starting motor wire from the starting relay, and unplug the spark plug cap and high-voltage wire.

4. Place the engine vertically. Remove the fixing screw of the cylinder head. Note that the screws should be loosened from both ends to the middle, and the screws should be removed three times. Lift the cylinder head, remove the cylinder cushion, and pay attention to the installation direction of the cylinder cushion. Loosen the oil release screw of the oil span shell and drain the oil in the oil span shell.

5. The disassembly of the engine is to put the engine removed from the frame on the workbench. 1: Place the engine upright, remove the inlet and exhaust manifolds and the cylinder head outlet pipes.